Home > Quality Control & IS Codes

IS codes for paints and allied products

Er. Parbhakar Dwivedi
0
 

       

It is base document outlining policy, procedures and endeavors to meet the requirement by three pronged strategy.

  1. Water Based Paints and Pigments
  2. Ready Mixed Paints,Enamels and Powder Coatings
  3. Thinners and Solvents
  4. Varnishes and Lacquers
1. Water Based Paints and Pigments
IS 427 : 2013 Specification for distemper, dry, colour as required (third revision)
IS 428 : 2013 Specification for washable distemper (third revision)
IS 5410 : 2013 Specification for cement paint (second revision)
IS 15489 : 2013 Specification for paint, plastic emulsion (first revision)
2. Ready Mixed Paints,Enamels and Powder Coatings
IS 101 : Methods of sampling and test for paints, varnishes and related products
IS 101 : (Part 1/Sec 1) : 1986 Test on liquid paints (general and (general and physical), Section 1 Sampling (third revision)
IS 101 : (Part 1/Sec 2) : 1987 Test on liquid paints (general and physical), Section 2 Preliminary examination and preparation of samples for testing (third revision)
IS 101 : (Part 1/Sec 3) : 1986 Test on liquid paints (general and physical), Section 3 Preparation of panels (third revision)
IS 101 : (Part 1/Sec 4) : 1987 Test on liquid paints (general and physical), Section 4 Brushing test (third revision)
IS 101 : (Part 1/Sec 5) : 1989 Test on liquid paints (general and physical), Section 5 Consistency (third revision)
IS 101 : (Part 1/Sec 6) : 1987 Test on liquid paints (general and physical), Section 6 Flash point (third revision)
IS 101 : (Part 1/Sec 7) : 1987 Test on liquid paints (general and physical), Section 7 Mass per 10 litres (third revision)
IS 101 : (Part 2/Sec 1) : 1988 Test on liquid paints (Chemical examination), Section 1 Water content (third revision)
IS 101 : (Part 2/Sec 2) : 1986 Test on liquid paints (Chemical examination), Section 2 Volatile matter (third revision)
IS 101 : (Part 3/Sec 1) : 1986 Tests on paint film formation, Section 1 Drying time (third revision)
IS 101 : (Part 3/Sec 2) : 1989 Tests on paint film formation, Section 2 Film thickness (third revision)
IS 101 : (Part 3/Sec 4) : 1987 Tests on paint film formation, Section 4 Finish (third revision)
IS 101 : (Part 3/Sec 5) : 1987 Tests on paint film formation, Section 5 Fineness of grind (third revision)
IS 101 : (Part 4/Sec 1) : 1988 Optical test, Section 1 Opacity (third revision)
IS 101 : (Part 4/Sec 2) : 1989 Optical test, Section 2 Colour (third revision)
IS 101 : (Part 4/Sec 3) : 1988 Optical test, Section 3 Light fastness test (third revision)
IS 101 : (Part 4/Sec 4) : 1988 Optical test, Section 4 Gloss (third revision)
IS 101 : (Part 5/Sec 1) : 1988 Mechanical test on paint films, Section 1 Hardness tests (third revision)
IS 101 : (Part 5/Sec 2) : 1988 Mechanical test on paint films, Section 2 Flexibility and adhesion (third revision)
IS 101 : (Part 5/Sec 3) : 1999 Mechanical test on paint films, Section 3 Impact resistance (fourth revision)
IS 101 : (Part 5/Sec 4) : 1988 Mechanical test on paint films, Section 4 Print free test (third revision)
IS 101 : (Part 6/Sec 1) : 1988 Durability tests, Section 1 Resistance to humidity under conditions of condensation (third revision)
IS 101 : (Part 6/Sec 2) : 1989 Durability tests, Section 2 Keeping properties (third revision)
IS 101 : (Part 6/Sec 3) : 1990 Durability tests, Section 3 Moisture vapour permeability (third revision)
IS 101 : (Part 6/Sec 4) : 1991 Durability tests, Section 4 Degradation of coatings (pictorial aids for evaluation) (third revision)
IS 101 : (Part 6/Sec 5) : Durability tests, Section 5 Accelerated weathering test
IS 101 : (Part 7/Sec 1) : 1989 Environmental tests on paint films, Section 1 Resistance to water (third revision)
IS 101 : (Part 7/Sec 2) : 1989 Environmental tests on paint films, Section 2 Resistance to liquids (third revision)
IS 101 : (Part 7/Sec 3) : 1990 Environmental tests on paint films, Section 3 Resistance to heat (third revision)
IS 101 : (Part 7/Sec 4) : 1990 Environmental tests on paint films, Section 4 Resistance to bleeding of pigments (third revision)
IS 101 : (Part 8/Sec 1) : 1989 Tests for pigments and other solids, Section 1 Residue on sieve (third revision)
IS 101 : (Part 8/Sec 2) : 1990 Tests for pigments and other solids, Section 2 Pigments and non .volatile matter (third revision)
IS 101 : (Part 8/Sec 3) : 1993 Tests for pigments and other solids, Section 3 Ash content (third revision)
IS 101 : (Part 8/Sec 4) : 2015 Tests for pigments and other solids, Section 4 Phthisic anhydride (fourth revision)
IS 101 : (Part 8/Sec 5) : 1993 Tests for pigments and other solids, Section 5 Lead restriction test (third revision)
IS 101 : (Part 8/Sec 6) : 1993 Tests for pigments and other solids, Section 6 Volume solids
IS 101 : (Part 9/Sec 1) : 1993 Tests for lacquers and varnish, Section 1 Acid value (third revision)
IS 101 : (Part 9/Sec 2) : 1993 Tests for lacquers and varnish, Section 2 Rosin test (third revision)
IS 104 : 1979 Specification for ready mixed paint, brushing, zinc chrome, priming (second revision)
IS 109 : 1968 Specification for ready mixed paint, brushing, priming, plaster to Indian Standard colours No. 361 and 631 (first revision)
IS 133 : 2004 Specification for enamel, interior (a) undercoating, (b) finishing (fourth revision)
IS 133 (Part 1) : 2013 Specification for enamel, interior a) undercoating, (b) finishing : Part 1 For household and decorative purposes (fifth revision)
IS 137 : 1965 Specification for ready mixed paint, brushing, matt or egg-shell flat, finishing, interior, to Indian Standard colour, as required (revised)
IS 158 : 2015 Specification for ready mixed paint, brushing, bituminous, black, lead- free, acid, alkali, and heat resisting (fourth revision)
IS 164 : 1981 Specification for ready mixed paint for road marking (second revision)
IS 168 : 1993 Specification for ready mixed paint, air-drying semi-glossy/matt, for general purposes
IS 341 : 1973 Specification for black Japan, Types A, B and C (first revision)
IS 2074 : 1992 Specification for ready mixed paint, air drying red oxide-zinc chrome, priming (second revision)
IS 2075 : 2000 Specification for ready mixed paint, stoving, red oxide-zinc chrome, priming (second revision)
IS 2339 : 2013 Specification for aluminium paint for general purposes (first revision)
IS 2932 (Part 1) : 2013 Specification for enamel, synthetic, exterior (a) undercoating, (b) finishing: Part 1 For household and decorative applications (fourth revision)
IS 2933 (Part 1) : 2013 Specification for enamel, exterior: (a) undercoating (b) finishing: Part 1 for domesic and decorative applications
IS 3536 : 1999 Specification for ready mixed paint, brushing, wood primer (first revision)
IS 3537 : 1966 Specification for ready mixed paint, finishing, interior for general purposes, to Indian Standard colours No. 101, 216, 217, 219, 275, 281, 352, 353, 358 to 361, 363, 364, 388, 410, 442, 444, 628, 631, 632, 634, 693, 697, white and black
IS 3539 : 1966 Specification for ready mixed paint, undercoating, for use under oil finishes, to Indian Standard colours, as required
IS 3585 : 1966 Specification for ready mixed paint, aluminium, brushing, priming, water resistant, for wood work
IS 3678 : 1966 Specification for ready mixed paint, thick white, for lettering
IS 9862 : 1981 Specification for ready mixed paint, brushing, bituminous black lead free, acid, alkali, water and chlorine resisting
IS 11883 : 1986 Specification for ready mixed paint, brushing, red oxide, priming for metals
IS 12744 (Part 1) : 2013 Specification for ready mixed paint, air drying, red oxide, zinc phosphate, priming: Part 1 for domestic and decorative applications (fourth revision)
IS 13183 : 1991 Specification for aluminium paints, heat resistant
IS 13213 : 1991 Specification for polyurethane full gloss enamel (two pack)
IS 13607 : 1992 Specification for ready mixed paint, finishing, general purposes, synthetic
IS 13871 : 1993 Specification for powder coatings
IS 14506 : 1998 Specification for epoxy red oxide zinc phosphate weld able primer, two component
IS 14589 : 1999 Specification for zinc priming paint, epoxy based, two pack
3. Thinners and Solvents
IS 82 : 1973 Methods of sampling and test for thinners and solvents for paints (first revision)
IS 430 : 1972 Paint remover, solvent type, non- flammable (second revision)
IS 431 : 1972 Paint remover, solvent type, flammable (second revision)
IS 533 : 2007 Specification for gum spirit of turpentine (oil of turpentine) (third revision)
IS 5667 : 1970 Specification for thinner for cellulose nitrate based paints and lacquers
IS 14314 : 1995 Specification for thinner general purposes for synthetic paints and varnishes
4. Varnishes and Lacquers
IS 337 : 1975 Specification for varnish, finishing, interior (first revision)
IS 344 : 1976 Specification for varnish, stoving (first revision)
IS 347 : 1975 Specification for varnish, shellac, for general purposes (first revision)
IS 348 : 1968 Specification for French polish (first revision)
IS 524 : 1983 Specification for varnish, finishing, exterior, synthetic (second revision)
IS 525 : 1968 Specification for varnish, finishing, exterior and general purposes (first revision)
IS 642 : 1963 Specification for varnish medium for aluminium paint (revised)
IS 10018 : 1981 Specification for lacquer, cellulose, nitrate clear, finishing, glossy for wood

Sponsored

PD Consulting Engineers Pvt. Ltd. Transforming construction for a new generation "Cost, Quality & Project management"

QS & Cost management, Bill Checking / Audit, Technical Auditors, Valuation, Contract and Tendering, Project Management, Project Planning, Quality Control, Consulting Engineers, Structural Consultancy

Close


Comment:

Name:

Email:

Civil N Construction Blog



Relevant Topics

Tests for stones

Tests For Limestone

Tests Of Mortar

Specifications For Water (IS 456)

Determine Flexure Strength Of Concrete

Procedure For Test Of Silt Content In Sand

Determination Of Dry Density Of Soil Core Cutter Method

Procedure For Determination Of Aggregate Crushing Value

Procedure For Slump Test For Concrete

Determination Of Water Absorption Coarse Aggregate Format

Initial And Final Setting Test Of Cement Format

Concrete Quantite Register Grade Wise Summary Format

Procedure For Determination Of Water Content In Soil

Procedure For Determination Of Elongation Index Of Coarse Aggregate

Aggregate Crushing Value Test Format

Water Test Report Register Format

Testing Of Cement Testing Of Cement Field Test

Procedure For Sieve Analysis Of Fine Aggregates

Compressive Strength Test Of Bricks Format

Efflorescence Status Of Bricks Format

Procedure For Determination Of Flakiness Index Of Coarse Aggregate

Sieve Analysis For Coarse Aggregate Format

Procedure For Determination Standard Consistency Of Cement

Method Of Sampling Of Cement

Verification Of Compression Testing Machine Oil Leakage

Rolling Margin Register Format

Determination Of Specific Geavity Fine Aggregate Format

Concrete Quantity Register Pouring Details Format

Procedure For Sieve Analysis Of Coarse Aggregates

Verification Of Cube Moulds

Dimension Test Of Bricks Format

Slump Ans Temp Register For Concrete Format

Procedure For Filling Cubes

Consistency Of Standared Cement Paste Format

Rolling Margin Register Total Quantity Format

Procedure For Determination Of Aggregate Impact Value

Determination Of Specific Gravity And Water Absorption Of Fine Aggregates

Procedure For Compressive Strength Testing For Concrete

Incoming Material Receiving Register Format

Determination Of Specific Gravity And Water Absorption Of Coarse Aggregate

Internal Qa And Qc Audit Observation Format

Verification Of Sieves

Verification Of Mechanical Weigh Balance

Determination Of Water Absorption Of Bricks

List Of Site Laboratory Equipment

Flakiness Index Of Coarse Aggregate Format

Determination Of Efflorescence Of Bricks

Determination Of Specific Gravity Coarse Aggregate Format

Procedure For Determination Fineness Of Cement

Concrete Cube Register Format

Concrete Quantity Register Month Wise Summary Format

Water Absorption Test Of Bricks Format

Moisture Correction Format

List Of Records To Be Maintained Qc Qa

Fineness Test Of Cement Format

Procedure For Determination Compressive Strength Test Of Cement

Aggregate Impact Value Test Format

Elongation Index Of Coarse Aggregate Format

Procedure For Determination Of Compressive Strength Of Bricks

Material Test Plan Civil Works

Soundness Test Of Cement Format

Procedure For Determination Setting Time Of Cement

Fineness Test Of Flyash Format

Field Dry Density Of Soil By Core Cutter Method Format

Bend And Reband Test Of Steel Format

Determination Of Water Absorption Fine Aggregate Format

Compressive Strength Test Of Cement Format

Sieve Analysis For Fine Aggregate Format

Verification Of Pan Balance

Calibration Plan

IS Codes for landscape developement and IS Codes for approaches to sustainability

IS Codes for steel and its alloys

IS Codes for stones

is-codes-for-structural-sections

IS Codes for threaded fasteners rivets and nails

IS Codes for timber bamboo and other lignocellulosic building materrials

IS Codes for waterproofing and damp proofing materials

IS Codes for building chemicals

IS Codes for building lime & products

IS Codes for clay & stabilized soil products

IS Codes for doors windows & ventilators

IS Codes for floor covering roofing & other finishes

IS Codes for glass & mortar

IS Codes for paints and allied products

IS Codes for polymers plastics & geosynthetics geotextiles

IS Codes gypsum based materials

IS Codes Safety and IS Codes For Demolition and Dismantling

IS Codes for Roofing

IS Codes for Steel Work

IS Codes for Finishing

IS Codes for Flooring

IS Codes for Stone Work

IS Codes for Wood Work

IS Codes for Brick Work

IS Codes for RCC Work

IS Codes for ConcreteWork

IS Codes for Mortar

IS Codes for composite matrix products

IS Codes for cement & concrete

IS Codes for builder's hardware

IS Codes for aluminium & other light metals & their alloys

Quality Control (QC), Quality Assurance (QA), Quality Control Utilizes Tools and techniques

Quality Assurance manual (QAM), Quality Assurance Plan (QAP)

Quality Audits, Quality Assurance Formulations

Quality Control Method Statement, Pre- Construction Stage, Construction Stage, Post- Construction Stage

Quality Control Plan, Quality Control System, Quality control of materials, Quality control of workers, Quality control of execution

IS Codes for air conditioning heating and mechanical ventilation

IS Codes for drainage and sanitation

IS Codes for electrical and allied installations

is codes for firefighting and life safety

IS Codes for lighting and natural ventilation

IS Codes for solid waste management and IS Codes for gas supply

is codes for thermal insulation materials

IS Codes for water supply

is codes for welding electrodes and wires

IS Codes for electrical wiring fittings and accessories

IS Codes for conductors & cables

IS Codes for sanitary appliances and water fittings

Sponsored

PD Consulting Engineers Pvt. Ltd. Transforming construction for a new generation "Cost, Quality & Project management"

QS & Cost management, Bill Checking / Audit, Technical Auditors, Valuation, Contract and Tendering, Project Management, Project Planning, Quality Control, Consulting Engineers, Structural Consultancy

Close