Home > Quality Control & IS Codes

IS Codes For SANITARY APPLIANCES AND WATER FITTINGS

Er. Parbhakar Dwivedi
0
 

       

a. General

b. Pipes and Fittings excluding valves-

  1. Brass and Copper Pipes and Fittings
  2. Cast Iron Pipes and Fittings
  3. Lead Pipes and Fittings
  4. Fibre Pipes and Fittings
  5. Plastic Pipes and Fittings
  6. Steel Tubes, Pipes and Fittings
  7. Stoneware Pipes and Fittings
a. General
IS 782 : 1978 Specification for caulking lead (third revision)
IS 804 : 1967 Specification for rectangular pressed steel tanks (first revision)
IS 1726 : 1991 Specification for cast iron manhole covers and frames (third revision)
IS 2963 : 2013 Specification for copper alloy waste fittings and waste plug for wash- basins and sinks (second revision)
IS 5219 : 2013 Specification for cast copper alloy traps (first revision)
IS 5455 : 1969 Specification for cast-iron steps for manholes
IS 5961 : 1970 Specification for cast iron gratings for drainage purposes
IS 9140 : 1996 Method of sampling of vitreous and fire clay sanitary appliances (second revision)
IS 9872 : 1981 Specification for precast concrete septic tanks
IS 12592 : 2002 Specification for precast concrete manhole covers and frames (first revision)
IS 12701 : 1996 Specification for rotational moulded polyethylene water storage tanks (first revision)
IS 13356 : 1992 Specification for precast Ferro cement water tanks (250 to 10 000 litres capacity)
IS 14399 : Hot press moulded thermosetting glass fibre reinforced (GRP) sectional water storage tanks
IS 14399 : (Part 1) : 1996 Specification for panels
IS 14399 : (Part 2) : 1996 Guidelines for assembly, installation and testing
b. Pipes and Fittings excluding valves

1. Brass and Copper Pipes and Fittings

IS 407 : 1981 Specification for brass tubes for general purposes (third revision)
IS 2501 : 1995 Specification for solid drawn copper tubes for general engineering purposes (third revision)

2. Cast Iron Pipes and Fittings

IS 1536 : 2001 Specification for centrifugally cast (spun) iron pressure pipes for water, gas and sewage (fourth revision)
IS 1537 : 1976 Specification for vertically cast iron pressure pipes for water, gas and sewage (first revision)
IS 1538 : 1993 Specification for cast iron fittings for pressure pipes for water, gas and sewage (third revision)
IS 1729 : 2002 Cast iron/ductile iron drainage pipes and pipe fittings for over ground non- pressure pipeline socket and spigot series (second revision)
IS 1879 : 2010 Specification for malleable cast iron pipe fittings (third revision)
IS 3989: 2009 Specification for centrifugally cast (spun) iron spigot and socket soil, waste and ventilating pipes, fittings and accessories (third revision)
IS 5531: 2014 Specification for cast iron specials for asbestos-cement pressure pipes for water, gas and sewage (third revision)
IS 6418 : 1971 Specification for cast iron and malleable cast iron flanges for general engineering purposes
IS 7181 : 1986 Specification for horizontally cast iron double flanged pipes for water, gas and sewage (first revision)
IS 8329 : 2000 Specification for centrifugally cast (spun) ductile iron pressure pipes for water, gas and sewage (third revision)
IS 8794 : 1988 Specification for cast iron detachable joints for use with asbestos cement pressure pipes (first revision)
IS 9523 : 2000 Specification for ductile iron fittings for pressure pipes for water, gas and sewage (first revision)
IS 10292 : 1988 Dimensional requirements for rubber sealing rings for C.I.D. Joints in asbestos cement piping (first revision)
IS 10299 : 1982 Cast iron saddle pieces for service connection from asbestos cement pressure pipes
IS 11606 : 1986 Methods of sampling cast iron pipes and fittings
IS 12820 : 2004 Dimensional requirements of rubber gaskets for mechanical joints and push-on joints for use with cast iron pipes and fittings for carrying water, gas and sewage (first revision)
IS 12987 : 1991 Cast iron detachable joints for use with asbestos cement pressure pipes (light duty)
IS 12988 : 1991 Rubber sealing rings for CID joints for light duty AC pipes. Dimensional requirements
IS 13382 : 2004 Specification for cast iron specials for mechanical and push-on flexible joints for pressure
IS 15905 : 2011 Specification for hub less centrifugally cast (spun) iron pipes, fittings and accessories. Spigot series

3. Lead Pipes and Fittings

404 (Part 1) : 1993 Specification for lead pipes: Part 1 For other than chemical purpose (third revision)

4. Fibre Pipes and Fittings

IS 11925 : 1986 Specification for pitch-impregnated fibre pipes and fittings for drainage purposes

5. Plastic Pipes and Fittings

IS 4984 : 1995 Specification for high density polyethylene pipes for water supply (fourth revision)
IS 4985 : 2000 Specification for unplasticized PVC pipes for potable water supplies (third revision)
IS 7834 : Specification for injection moulded PVC socket fittings with solvent cement joints for water supplies
IS 7834 : (Part 1) : 1987 General requirements (first revision)
IS 7834 : (Part 2) : 1987 Specific requirements for 45° elbows (first revision)
IS 7834 : (Part 3) : 1987 Specific requirements for 90° elbows (first revision)
IS 7834 : (Part 4) : 1987 Specific requirements for 90° tees (first revision)
IS 7834 : (Part 5) : 1987 Specific requirements for 45° tees (first revision)
IS 7834 : (Part 6) : 1987 Specific requirements for sockets (first revision)
IS 7834 : (Part 7) : 1987 Specific requirements for unions (first revision)
IS 7834 : (Part 8) : 1987 Specific requirements for caps (first revision)
IS 8008 : Specification for injection moulded high density polyethylene (HDPE) fittings for potable water supplies
IS 8008 : (Part 1) : 2003 General requirements
IS 8008 : (Part 2) : 2003 Specific requirements for 90° bends (first revision)
IS 8008 : (Part 3) : 2003 Specific requirements for 90° tees
IS 8008 : (Part 4) : 2003 Specific requirements for reducers
IS 8008 : (Part 5) : 2003 Specific requirements for ferrule reducers (first revision)
IS 8008 : (Part 6) : 2003 Specific requirements for pipe ends
IS 8008 : (Part 7) : 2003 Specific requirements for sandwich flanges
IS 8008 : (Part 8) : 2003 Specific requirements for reducing tests
IS 8008 : (Part 9) : 2003 Specific requirements for end caps (first revision)
IS 8360 : Specification for fabricated high density polyethylene (HDPE) fittings for potable water supplies
IS 8360 : (Part 1) : 1977 General requirements
IS 8360 : (Part 2) : 1977 Specific requirements for 90° tees
IS 8360 : (Part 3) : 1977 Specific requirements for 90° bends
IS 10124 : Specification for fabricated PVC-U fittings for potable water supplies
IS 10124 : (Part 1) : 2009 General requirements (second revision)
IS 10124 : (Part 2) : 2009 Specific requirements for sockets (second revision)
IS 10124 : (Part 3) : 2009 Specific requirements of straight reducers (second revision)
IS 10124 : (Part 4) : 2009 Specific requirements for caps (second revision)
IS 10124 : (Part 5) : 2009 Specific requirements for equal tees (second revision)
IS 10124 : (Part 6) : 2009 Specific requirements for flanged tail piece with metallic flanges (second revision)
IS 10124 : (Part 7) : 2009 Specific requirements for threaded adaptors (second revision)
IS 10124 : (Part 8) : 2009 Specific requirements for 90° bends (second revision)
IS 10124 : (Part 9) : 2009 Specific requirements for 60° bends (second revision)
IS 10124 : (Part 10) : 2009 Specific requirements for 45° bends (second revision)
IS 10124 : (Part 11) : 2009 Specific requirements for 30° bends (second revision)
IS 10124 : (Part 12) : 2009 Specific requirements for 22½° bends (second revision)
IS 10124 : (Part 13) : 2009 Specific requirements for 11¼° bends (second revision)
IS 12235 : Methods of test for unplasticized PVC pipes for potable water supplies
IS 12235 : (Part 1) : 2004 Measurement of dimensions (first revision)
IS 12235 : (Part 2) : 2004 Determination of Vicat softening temperature (first revision)
IS 12235 : (Part 3) : 2004 Test for opacity (first revision)
IS 12235 : (Part 4) : 2004 Determining the detrimental effect on the composition of water (first revision)
IS 12235 : (Part 5/Sec 1) : 2004 Longitudinal reversion, Section 1 Determination methods (first revision)
IS 12235 : (Part 5/Sec 2) : 2004 Reversion test, Section 2 Determination parameters (first revision)
IS 12235 : (Part 6) : 2004 Stress relief test (first revision)
IS 12235 : (Part 7) : 2004 Resistance to sulphuric acid (first revision)
IS 12235 : (Part 8/Sec 1) : 2004 Resistance to internal hydrostatic pressure, Section 1 Resistance to internal hydrostatic pressure at constant internal water pressure (first revision)
IS 12235 : (Part 8/Sec 2) : 2004 Resistance to internal hydrostatic pressure, Section 2 Leak-tightness of elastomeric sealing ring type socket joints under positive internal pressure and with angular deflection (first revision)
IS 12235 : (Part 8/Sec 3) : 2004 Resistance to internal hydrostatic pressure, Section 3 Leak-tightness of elastomeric sealing ring type socket joints under negative internal pressure and with angular deflection (first revision)
IS 12235 : (Part 8/Sec 4) : 2004 Resistance to internal hydrostatic pressure, Section 4 Leak-tightness of elastomeric sealing ring type socket joints under positive internal pressure without angular deflection (first revision)
IS 12235 : (Part 9) : 2004 Resistance to external blows (impact resistance) at 0°C (Round-the-clock method)
IS 12235 : (Part 10) : 2004 Determination of organotin as tin aqueous solution (first revision)
IS 12235 : (Part 11) : 2004 Resistance to dichloromethane at specified temperature (first revision)
IS 12235 : (Part 12) : 2004 Determination of titanium dioxide content
IS 12235 : (Part 13) : 2004 Determination of tensile strength and elongation
IS 12235 : (Part 14) : 2004 Determination of density/relative density (specific gravity)
IS 12235 : (Part 15) : 2004 Determination of vinyl chloride monomer content
IS 12235 : (Part 16) : 2004 High temperature test
IS 12235 : (Part 17) : 2004 Determination of ash content and sulphated ash content
IS 12235 : (Part 18) : 2004 Determination of ring stiffness
IS 12235 : (Part 19) : 2004 Flattening test
IS 12709 : 1994 Specification for glass-fibre reinforced plastic (GRP) pipes joints and fittings for use for potable water supply (first revision)
IS 12818 : 2010 Specification for unplasticized polyvinyl chloride(PVC-U) screen and casing pipes for bore/tube wells (second revision)
IS 13592 : 2013 Specification for unplasticized polyvinyl chloride (PVC-U) pipes for soil and waste discharge system for  inside and outside buildings including ventilation and rainwater system (first revision)
IS 14333 : 1996 Specification for high density polyethylene pipes for sewerage
IS 14402 : 1996 Specification for GRP pipes, joints and fittings for use for sewerage, industrial waste and water (other than potable)
IS 14735 : 1999 Specification for unplasticized polyvinyl chloride (UPVC) injection moulded fittings for soil and waste discharge system for inside and outside buildings including ventilation and rain water system
IS 14885 : 2001 Specification for polyethylene pipe for supply of gaseous fuel
IS 15328 : 2003 Specification for unplasticized non- pressure polyvinyl chloride (PVC-U) pipes for use in underground drainage and sewerage system
IS 15450 : 2004 Specification for polyethylene/ aluminium/polyethylene composite pressure pipes for hot and cold water supplies
IS 15778 : 2007 Specification for chlorinated polyvinyl chloride (CPVC) pipes for potable hot and cold water distribution supplies
IS 15801 : 2008 Specification for polypropylene- random copolymer pipes for hot and cold water supplies
IS 15927 : Specification for polyethylene fittings for use with polyethylene pipes for the supply of gaseous fuels
IS 15927 : (Part 1) : 2012 Fittings for sockets using heated tools
IS 15927 : (Part 2) : 2012 Spigot fittings for butt fusion jointing or socket fusion using heated tools, spigot fittings for use with electro- fusion fittings
IS 15927 : (Part 3) : 2011 Electro-fusion fittings
IS 16098 : Specification for structured – wall plastics piping systems for non- pressure drainage and sewerage
IS 16098 : (Part 1) : 2013 Pipes and fittings with smooth external surface, Type A
IS 16098 : (Part 2) : 2013 Pipes and fittings with non-smooth external surface, Type B 

6. Steel Tubes, Pipes and Fittings

IS 1239 : Specification for steel tubes, tubular and other wrought steel fittings
IS 1239 : (Part 1) : 2004 Steel tubes (sixth revision)
IS 1239 : (Part 2) : 2011 Steel pipe fittings (fifth revision)
IS 3589 : 2001 Specification for steel pipes for water and sewage (168.3 to 2 540 mm outside diameter) (third revision)
IS 4270 : 2001 Specification for steel tubes used for water wells (third revision)
IS 5504 : 1997 Specification for spiral welded pipes (first revision)
IS 6286 : 1979 Seamless and welded steel pipe for sub-zero temperature service
IS 6392 : 1971 Steel pipe flanges

7. Stoneware Pipes and Fittings

IS 651 : 2007 Specification for glazed stoneware pipes and fittings (sixth revision)
IS 3006 : 1979 Specification for chemically resistant glazed stoneware pipes and fittings (first revision)

Sponsored

PD Consulting Engineers Pvt. Ltd. Transforming construction for a new generation "Cost, Quality & Project management"

QS & Cost management, Bill Checking / Audit, Technical Auditors, Valuation, Contract and Tendering, Project Management, Project Planning, Quality Control, Consulting Engineers, Structural Consultancy

Close


Comment:

Name:

Email:

Civil N Construction Blog



Relevant Topics

Tests for stones

Tests For Limestone

Tests Of Mortar

Specifications For Water (IS 456)

Determine Flexure Strength Of Concrete

Procedure For Test Of Silt Content In Sand

Determination Of Dry Density Of Soil Core Cutter Method

Procedure For Determination Of Aggregate Crushing Value

Procedure For Slump Test For Concrete

Determination Of Water Absorption Coarse Aggregate Format

Initial And Final Setting Test Of Cement Format

Concrete Quantite Register Grade Wise Summary Format

Procedure For Determination Of Water Content In Soil

Procedure For Determination Of Elongation Index Of Coarse Aggregate

Aggregate Crushing Value Test Format

Water Test Report Register Format

Testing Of Cement Testing Of Cement Field Test

Procedure For Sieve Analysis Of Fine Aggregates

Compressive Strength Test Of Bricks Format

Efflorescence Status Of Bricks Format

Procedure For Determination Of Flakiness Index Of Coarse Aggregate

Sieve Analysis For Coarse Aggregate Format

Procedure For Determination Standard Consistency Of Cement

Method Of Sampling Of Cement

Verification Of Compression Testing Machine Oil Leakage

Rolling Margin Register Format

Determination Of Specific Geavity Fine Aggregate Format

Concrete Quantity Register Pouring Details Format

Procedure For Sieve Analysis Of Coarse Aggregates

Verification Of Cube Moulds

Dimension Test Of Bricks Format

Slump Ans Temp Register For Concrete Format

Procedure For Filling Cubes

Consistency Of Standared Cement Paste Format

Rolling Margin Register Total Quantity Format

Procedure For Determination Of Aggregate Impact Value

Determination Of Specific Gravity And Water Absorption Of Fine Aggregates

Procedure For Compressive Strength Testing For Concrete

Incoming Material Receiving Register Format

Determination Of Specific Gravity And Water Absorption Of Coarse Aggregate

Internal Qa And Qc Audit Observation Format

Verification Of Sieves

Verification Of Mechanical Weigh Balance

Determination Of Water Absorption Of Bricks

List Of Site Laboratory Equipment

Flakiness Index Of Coarse Aggregate Format

Determination Of Efflorescence Of Bricks

Determination Of Specific Gravity Coarse Aggregate Format

Procedure For Determination Fineness Of Cement

Concrete Cube Register Format

Concrete Quantity Register Month Wise Summary Format

Water Absorption Test Of Bricks Format

Moisture Correction Format

List Of Records To Be Maintained Qc Qa

Fineness Test Of Cement Format

Procedure For Determination Compressive Strength Test Of Cement

Aggregate Impact Value Test Format

Elongation Index Of Coarse Aggregate Format

Procedure For Determination Of Compressive Strength Of Bricks

Material Test Plan Civil Works

Soundness Test Of Cement Format

Procedure For Determination Setting Time Of Cement

Fineness Test Of Flyash Format

Field Dry Density Of Soil By Core Cutter Method Format

Bend And Reband Test Of Steel Format

Determination Of Water Absorption Fine Aggregate Format

Compressive Strength Test Of Cement Format

Sieve Analysis For Fine Aggregate Format

Verification Of Pan Balance

Calibration Plan

IS Codes for landscape developement and IS Codes for approaches to sustainability

IS Codes for steel and its alloys

IS Codes for stones

is-codes-for-structural-sections

IS Codes for threaded fasteners rivets and nails

IS Codes for timber bamboo and other lignocellulosic building materrials

IS Codes for waterproofing and damp proofing materials

IS Codes for building chemicals

IS Codes for building lime & products

IS Codes for clay & stabilized soil products

IS Codes for doors windows & ventilators

IS Codes for floor covering roofing & other finishes

IS Codes for glass & mortar

IS Codes for paints and allied products

IS Codes for polymers plastics & geosynthetics geotextiles

IS Codes gypsum based materials

IS Codes Safety and IS Codes For Demolition and Dismantling

IS Codes for Roofing

IS Codes for Steel Work

IS Codes for Finishing

IS Codes for Flooring

IS Codes for Stone Work

IS Codes for Wood Work

IS Codes for Brick Work

IS Codes for RCC Work

IS Codes for ConcreteWork

IS Codes for Mortar

IS Codes for composite matrix products

IS Codes for cement & concrete

IS Codes for builder's hardware

IS Codes for aluminium & other light metals & their alloys

Quality Control (QC), Quality Assurance (QA), Quality Control Utilizes Tools and techniques

Quality Assurance manual (QAM), Quality Assurance Plan (QAP)

Quality Audits, Quality Assurance Formulations

Quality Control Method Statement, Pre- Construction Stage, Construction Stage, Post- Construction Stage

Quality Control Plan, Quality Control System, Quality control of materials, Quality control of workers, Quality control of execution

IS Codes for air conditioning heating and mechanical ventilation

IS Codes for drainage and sanitation

IS Codes for electrical and allied installations

is codes for firefighting and life safety

IS Codes for lighting and natural ventilation

IS Codes for solid waste management and IS Codes for gas supply

is codes for thermal insulation materials

IS Codes for water supply

is codes for welding electrodes and wires

IS Codes for electrical wiring fittings and accessories

IS Codes for conductors & cables

IS Codes for sanitary appliances and water fittings

Sponsored

PD Consulting Engineers Pvt. Ltd. Transforming construction for a new generation "Cost, Quality & Project management"

QS & Cost management, Bill Checking / Audit, Technical Auditors, Valuation, Contract and Tendering, Project Management, Project Planning, Quality Control, Consulting Engineers, Structural Consultancy

Close