Home > Quality Control & IS Codes

IS Codes For THREADED FASTENERS, RIVETS AND NAILS

Er. Parbhakar Dwivedi
0
 

       

IS Codes For THREADED FASTENERS, RIVETS AND NAILS:
IS 207 : 1964 Specification for gate and shutter hooks and eyes (revised)
IS 451 : 1999 Specification for technical supply conditions for wood screws (third revision)
IS 554 : 1999 Specification for pipe threads where pressure-tide joints are made on the threads. Dimensions, tolerances and designation (fourth revision)
IS 723 : 1972 Specification for steel countersunk head wire nails (second revision)
IS 724 : 1964 Specification for mild steel and brass cup, ruler and square hooks and screw eyes (revised)
IS 725 : 1961 Specification for copper wire nails (revised)
IS 730 : 1978 Specification for hook bolts for corrugated sheet roofing (second revision)
IS 1120 : 1975 Specification for coach screws (first revision)
IS 1363 : (Part 1) : 2002 Specification for hexagon head bolts, screws and nuts of product grade C Hexagon head bolts (Size range M5 to M64) (fourth revision)
IS 1363 : (Part 2) : 2002 Hexagon head screws (Size range M5 to M64) (fourth revision)
IS 1363 : (Part 3) : 2002 Hexagon nuts (Size range M5 to M64) (fourth revision)
1364 : (Part 1) : 2002 Specification for hexagon head bolts, screws and nuts of product Grades A and B Hexagon head bolts (Size range M1.6 to M64) (fourth revision)
1364 : (Part 2) : 2002 Hexagon head screws (Size range M1.6 to M64) (fourth revision)
1364 : (Part 3) : 2002 Hexagon nuts (Size range M1.6 to M64) (fourth revision)
1364 : (Part 4) : 2003 Hexagon thin nuts (chamfered) (Size range M1.6 to M64) (fourth revision)
1364 : (Part 5) : 2002 Hexagon thin nuts (unchamfered) (Size range M1.6 to M10) (fourth revision)
1364 : (Part 6) : 2002 Hexagon nuts, style 2
IS 1365 : 2005 Slotted countersunk flat head screws (Common head style) . Product Grade A (fourth revision)
IS 1366 : 2002 Specification for slotted cheese head screws (third revision)
IS 1367 Specification for technical supply conditions for threaded steel fasteners
IS 1367 : (Part 1) : 2014 Introduction and general information (fourth revision)
IS 1367 : (Part 2) : 2002 Product grades and tolerances (third revision)
IS 1367 : (Part 3) : 2002 Mechanical properties and test methods for bolts, screws and studs with full load ability (fourth revision)
IS 1367 : (Part 5) : 2002 Mechanical properties and test methods for set screws and similar threaded fasteners not under tensile stresses (third revision)
IS 1367 : (Part 6) : 1994 Mechanical properties and test methods for nuts with specified proof loads (third revision)
IS 1367 : (Part 7) : 1980 Mechanical properties and test methods for nuts without specified proof loads (second revision)
IS 1367 : (Part 8) : 2014 Mechanical and performance properties for prevailing torque type steel hexagon nuts (fourth revision)
IS 1367 : (Part 9/Sec 1) : 1993 Surface discontinuities, Section 1 Bolts, screws and studs for general applications (third revision)
IS 1367 : (Part 9/Sec 2) : 1993 Surface discontinuities, Section 2 Bolts, screws and studs for special applications (third revision)
IS 1367 : (Part 10) : 2002 Surface discontinuities on nuts (third revision)
IS 1367 : (Part 11) : 2002 Electroplated coatings (third revision)
IS 1367 : (Part 12) : 1981 Phosphate coatings on threaded fasteners (second revision)
IS 1367 : (Part 13) : 1983 Hot dip galvanized coatings on threaded fasteners (second revision)
IS 1367 : (Part 14/Sec 1) : 2002 Mechanical properties of corrosion resistance stainless stainless steel fasteners, Section 1 Bolts, screws and studs (third revision)
IS 1367 : (Part 14/Sec 2) : 2002 Mechanical properties of corrosion resistance stainless stainless steel fasteners, Section 2 Nuts (third revision)
IS 1367 : (Part 14/Sec 3) : 2002 Mechanical properties of corrosion resistance stainless stainless steel fasteners, Section 3 Set screws and similar fasteners not under tensile stress (third revision)
IS 1367 : (Part 16) : 2002 Designation system and symbols (third revision)
IS 1367 : (Part 17) : 2005 Inspections, sampling and acceptance procedure (fourth revision)
IS 1367 : (Part 18) : 1996 Packaging (third revision)
IS 1367 : (Part 19) : 1996 Axial fatigue testing of bolts, screws and studs
IS 1367 : (Part 20) : 1996 Torsional test and minimum torques for bolts and screws with nominal diameters 1mm to 10 mm
IS 1929 : 1982 Specification for hot forged steel rivets for hot closing (12 to 36 mm diameter) (first revision)
IS 2016 : 1967 Specification for plain washers (first revision)
IS 2155 : 1982 Specification for cold forged solid steel rivets for hot closing (6 to 16 mm diameter) (first revision)
IS 2269 : 2006 Hexagon socket head cap screws (fifth revision)
IS 2585 : 2006 Specification for square head bolts, screws and square nuts of product grade C (second revision)
IS 2609 : 1972 Specification for coach bolts (first revision)
IS 2643 : 2005 Pipe threads where pressure-tight joints are not made on the threads. Dimensions, tolerances and designation (third revision)
IS 2687 : 1991 Specification for cap nuts (second revision)
IS 2769 : 1969 Sizes for squares and square holes for general engineering purposes (first revision)
IS 2907 : 1998 Specification for non-ferrous rivets (first revision)
IS 2998 : 1982 Specification for cold forged steel rivets for cold closing (1 to 16 mm diameter) (first revision)
IS 3063 : 1994 Specification for fasteners single coil rectangular section spring lock washers (second revision)
IS 3121 : 1981 Specification for rigging screws and stretching screws (first revision)
IS 3468 : 1991 Specification for pipe nuts (second revision)
IS 3640 : 1982 Specification for hexagon fit bolts (first revision)
IS 3757 : 1985 Specification for high strength structural bolts (second revision)
IS 4206 : 1987 Dimensions for nominal lengths, and thread lengths for bolts, screws and studs (first revision)
IS 4762 : 2002 Specification for worm drive hose clips for general purposes (second revision)
IS 5369 : 1975 General requirements for plain washers and lock washers (first revision)
IS 5370 : 1969 Specification for plain washers with outside diameter 3 × inside diameter
IS 5372 : 1975 Specification for taper washer for channels (ISMC) (first revision)
IS 5373 : 1969 Specification for square washers for wood fastenings
IS 5374 : 1975 Specification for taper washers for l-beam (ISMB) (first revision)
IS 5624 : 1993 Specification for foundation bolts (first revision)
IS 6113 : 1970 Specification for aluminium fasteners for building purposes
IS 6610 : 1972 Specification for heavy washers for steel structures
IS 6623 : 2004 Specification for high strength structural nuts (second revision)
IS 6639 : 2005 Specification for hexagon head bolts for general steel structures (first revision)
IS 6649 : 1985 Specification for hardened and tempered washers for high strength structural bolts and nuts (first revision)
IS 6733 : 1972 Specification for wall and roofing nails
IS 6736 : 1972 Specification for slotted raised countersunk head wood screws
IS 6739 : 1972 Specification for slotted round head wood screws
IS 6760 : 1972 Specification for slotted countersunk head wood screws
IS 8033 : 1976 Specification for washers with square hole for wood fastenings
IS 8412 : 1977 Specification for slotted countersunk head bolts for steel structures
IS 8822 : 1978 Specification for slotted mushroom head roofing bolts
IS 8869 : 1978 Specification for washers for corrugated sheet roofing
IS 8911 : 2005 Countersunk slotted raised head screws (common head style). Product Grade A (first revision)
IS 10102 : 1982 Specification for technical supply conditions for rivets
IS 10238 : 2001 Specification for step bolts for steel structures
IS 12427 : 2001 Specification for threaded steel fasteners. hexagon head transmission tower bolts (first revision)

Sponsored

PD Consulting Engineers Pvt. Ltd. Transforming construction for a new generation "Cost, Quality & Project management"

QS & Cost management, Bill Checking / Audit, Technical Auditors, Valuation, Contract and Tendering, Project Management, Project Planning, Quality Control, Consulting Engineers, Structural Consultancy

Close


Comment:

Name:

Email:

Civil N Construction Blog



Relevant Topics

Tests for stones

Tests For Limestone

Tests Of Mortar

Specifications For Water (IS 456)

Determine Flexure Strength Of Concrete

Procedure For Test Of Silt Content In Sand

Determination Of Dry Density Of Soil Core Cutter Method

Procedure For Determination Of Aggregate Crushing Value

Procedure For Slump Test For Concrete

Determination Of Water Absorption Coarse Aggregate Format

Initial And Final Setting Test Of Cement Format

Concrete Quantite Register Grade Wise Summary Format

Procedure For Determination Of Water Content In Soil

Procedure For Determination Of Elongation Index Of Coarse Aggregate

Aggregate Crushing Value Test Format

Water Test Report Register Format

Testing Of Cement Testing Of Cement Field Test

Procedure For Sieve Analysis Of Fine Aggregates

Compressive Strength Test Of Bricks Format

Efflorescence Status Of Bricks Format

Procedure For Determination Of Flakiness Index Of Coarse Aggregate

Sieve Analysis For Coarse Aggregate Format

Procedure For Determination Standard Consistency Of Cement

Method Of Sampling Of Cement

Verification Of Compression Testing Machine Oil Leakage

Rolling Margin Register Format

Determination Of Specific Geavity Fine Aggregate Format

Concrete Quantity Register Pouring Details Format

Procedure For Sieve Analysis Of Coarse Aggregates

Verification Of Cube Moulds

Dimension Test Of Bricks Format

Slump Ans Temp Register For Concrete Format

Procedure For Filling Cubes

Consistency Of Standared Cement Paste Format

Rolling Margin Register Total Quantity Format

Procedure For Determination Of Aggregate Impact Value

Determination Of Specific Gravity And Water Absorption Of Fine Aggregates

Procedure For Compressive Strength Testing For Concrete

Incoming Material Receiving Register Format

Determination Of Specific Gravity And Water Absorption Of Coarse Aggregate

Internal Qa And Qc Audit Observation Format

Verification Of Sieves

Verification Of Mechanical Weigh Balance

Determination Of Water Absorption Of Bricks

List Of Site Laboratory Equipment

Flakiness Index Of Coarse Aggregate Format

Determination Of Efflorescence Of Bricks

Determination Of Specific Gravity Coarse Aggregate Format

Procedure For Determination Fineness Of Cement

Concrete Cube Register Format

Concrete Quantity Register Month Wise Summary Format

Water Absorption Test Of Bricks Format

Moisture Correction Format

List Of Records To Be Maintained Qc Qa

Fineness Test Of Cement Format

Procedure For Determination Compressive Strength Test Of Cement

Aggregate Impact Value Test Format

Elongation Index Of Coarse Aggregate Format

Procedure For Determination Of Compressive Strength Of Bricks

Material Test Plan Civil Works

Soundness Test Of Cement Format

Procedure For Determination Setting Time Of Cement

Fineness Test Of Flyash Format

Field Dry Density Of Soil By Core Cutter Method Format

Bend And Reband Test Of Steel Format

Determination Of Water Absorption Fine Aggregate Format

Compressive Strength Test Of Cement Format

Sieve Analysis For Fine Aggregate Format

Verification Of Pan Balance

Calibration Plan

IS Codes for landscape developement and IS Codes for approaches to sustainability

IS Codes for steel and its alloys

IS Codes for stones

is-codes-for-structural-sections

IS Codes for threaded fasteners rivets and nails

IS Codes for timber bamboo and other lignocellulosic building materrials

IS Codes for waterproofing and damp proofing materials

IS Codes for building chemicals

IS Codes for building lime & products

IS Codes for clay & stabilized soil products

IS Codes for doors windows & ventilators

IS Codes for floor covering roofing & other finishes

IS Codes for glass & mortar

IS Codes for paints and allied products

IS Codes for polymers plastics & geosynthetics geotextiles

IS Codes gypsum based materials

IS Codes Safety and IS Codes For Demolition and Dismantling

IS Codes for Roofing

IS Codes for Steel Work

IS Codes for Finishing

IS Codes for Flooring

IS Codes for Stone Work

IS Codes for Wood Work

IS Codes for Brick Work

IS Codes for RCC Work

IS Codes for ConcreteWork

IS Codes for Mortar

IS Codes for composite matrix products

IS Codes for cement & concrete

IS Codes for builder's hardware

IS Codes for aluminium & other light metals & their alloys

Quality Control (QC), Quality Assurance (QA), Quality Control Utilizes Tools and techniques

Quality Assurance manual (QAM), Quality Assurance Plan (QAP)

Quality Audits, Quality Assurance Formulations

Quality Control Method Statement, Pre- Construction Stage, Construction Stage, Post- Construction Stage

Quality Control Plan, Quality Control System, Quality control of materials, Quality control of workers, Quality control of execution

IS Codes for air conditioning heating and mechanical ventilation

IS Codes for drainage and sanitation

IS Codes for electrical and allied installations

is codes for firefighting and life safety

IS Codes for lighting and natural ventilation

IS Codes for solid waste management and IS Codes for gas supply

is codes for thermal insulation materials

IS Codes for water supply

is codes for welding electrodes and wires

IS Codes for electrical wiring fittings and accessories

IS Codes for conductors & cables

IS Codes for sanitary appliances and water fittings

Sponsored

PD Consulting Engineers Pvt. Ltd. Transforming construction for a new generation "Cost, Quality & Project management"

QS & Cost management, Bill Checking / Audit, Technical Auditors, Valuation, Contract and Tendering, Project Management, Project Planning, Quality Control, Consulting Engineers, Structural Consultancy

Close